E1M-AEN

§ Specs in detail

§ Interface map

Hover an interface to see where it lands on the module footprint. Counts and groups below.

§ Ordering options

Alp Lab supports custom options.Contact salesfor a quote.

§ Module gallery

Photography and block diagrams of E1M-AEN. Click any image to zoom.

FrontZoom ↗

BackZoom ↗

Block diagramZoom ↗

§ Where to buy

Order E1M-AEN through our distributors

Order modules, dev kits, and production quantities. Local stock, local logistics, local support.

United Kingdom · Global

Astute Electronics

Visit distributor ↗

Germany · EU

Endrich Bauelemente

Visit distributor ↗

Israel · Levant

NISKO

Visit distributor ↗

§ Documentation

Downloads — datasheets, CAD and design files.

Full documentation on docs.alplab.ai ↗

§ Compliance & regulatory

Module-level declarations for E1M-AEN.

Material declarations and reliability data for the module itself. No sales gate — request a copy for design-in or audit purposes.

End-product CE / FCC / UKCA marking is the integrator's responsibility. See /compliance for what we ship vs what's yours.

§ Run on this SoM

§ Run on this SoM in 30 seconds

Same C/C++ API across every E1M module.

Drop a board config at the project root, point at your SKU, and the Alp SDK builds Zephyr / bare-metal firmware (Linux on the Cortex-A32 is planned; no Yocto build yet) for E1M-AEN with no per-chip rewrites. Swap to another E1M module by changing one line.

# E1M-AEN firmware project
som:
  sku: E1M-AEN801
  hw_rev: r2

preset: e1m-evk

cores:
  bare_metal:
    os: bare-metal
    app: ./fw
    peripherals: [gpio, i2c, uart]

#include <alp/peripheral.h>
#include <alp/e1m_pinout.h>

int main(void) {
  alp_gpio_t       *led = alp_gpio_open(ALP_E1M_GPIO_IO0);
  alp_i2c_config_t  cfg = ALP_I2C_CONFIG_DEFAULT(ALP_E1M_I2C0);
  alp_i2c_t        *bus = alp_i2c_open(&cfg);
  uint8_t reg = 0x00, buf[2];

  while (1) {
    alp_gpio_write(led, 1);
    /* read register 0x00 of your carrier sensor (example address 0x1D).
   0x50 / 0x58 on I2C0 is the module's identity EEPROM: read-only,
   never put another device there */
    alp_i2c_write_read(bus, 0x1D, &reg, 1, buf, sizeof buf);
    alp_gpio_write(led, 0);
  }
}

$ curl -fsSL https://raw.githubusercontent.com/alplabai/tan-cli/main/install.sh | sh
# Windows: irm https://raw.githubusercontent.com/alplabai/tan-cli/main/install.ps1 | iex
$ git clone https://github.com/alplabai/alp-sdk
$ tan bootstrap --sdk-root ./alp-sdk   # west workspace, venv, toolchain
$ tan doctor                           # build / flash readiness check
$ tan init --name my-app && cd my-app
$ tan validate                         # schema + pin allocation check
$ tan build                            # bare-metal build for E1M-AEN801
# flash: modules ship with a factory MCUboot. Load zephyr.signed.bin into the
# Cortex-M55 HE slot0 at 0x80010000 with a J-Link on J2 (JLinkExe: loadbin
# <file> 0x80010000; the on-board RP2040 debugger on J5 is the alternative).
# See the E1M EVK Getting Started guide. Do not use west flash on a
# pre-provisioned module, and never pass --replace-atoc.

§ Compare with siblings

No sibling variants in this family yet.

§ Related